Volume & Issue: Volume 13, Issue 4 - Serial Number 47, Autumn 2024 
Research Paper Petroleum Engineering

Experimental and Modeling of Rheology and Swelling Behavior of Preformed Particle Gel

https://doi.org/10.22050/ijogst.2026.582976.1780

Bahram Soltani Soulgani, Abdolnabi Hashemi, Seyed Amin Moosavi, pourya malmir

Abstract Excessive water production represents a significant economic and operational burden in the petroleum industry, necessitating sophisticated control measures to mitigate costs associated with water oil separation, scale formation, and equipment corrosion. This investigation characterizes the performance of preformed particle gels (PPG) as a robust chemical water shutoff treatment through comprehensive rheological and swelling kinetics studies. Experimental results demonstrate that PPG viscosity is highly sensitive to concentration; specifically, a twofold increase in concentration (from 2500 to 5500 ppm) results in a tenfold increase in viscosity. The rheological behavior was successfully modeled using the Cross equation, facilitating the derivation of a unified mathematical model that predicts viscosity as a function of concentration and shear rate. Crucially, at a calculated shear rate of 0.14 s⁻¹ based on the assumption that injection velocity is 100 times the reservoir oil movement PPG maintains sufficient viscosity for effective flow diversion. Furthermore, the study explores the influence of agitation and salinity on swelling performance. Stirring was found to accelerate swelling kinetics, shifting the mechanism from Fickian diffusion at zero RPM to a transport dominated mechanism (n ≈ 0.85) due to the simultaneous activation of multiple diffusion pathways. Salinity experiments utilizing KCl and MgCl₂ reveal that divalent cations (Mg²⁺) are significantly more effective at inhibiting swelling than monovalent cations (K⁺) due to charge neutralization of carboxylate groups. Morphological analysis via Scanning Electron Microscopy (SEM) suggests that ions with larger radii obstruct the gel pores, a phenomenon that can be mitigated during synthesis through the introduction of nonionic hydrophilic monomers and pore forming agents such as ethanol or ammonium bicarbonate. Finally, the research identifies diffusion limited aggregation (DLA) as the dominant growth mechanism. Modified DLA models were developed to predict salinity dependent swelling, providing a rigorous framework for optimizing PPG treatments in heterogeneous reservoirs

Research Paper Petroleum Engineering – Drilling

Effects of Alum on Rheology, Filtration, and Shale Swelling in Water-Based Drilling Fluids: Identification of a Narrow Operational Window and Swelling Reversal in Calcareous Formations

https://doi.org/10.22050/ijogst.2026.584586.1782

Alireza Ahmadi, Khalil Shahbazi, Mahdi Shojaei

Abstract Drilling fluids require effective shale inhibition while maintaining rheology and fluid-loss control, especially in polymer-based water-based drilling fluids (WBMs). Alum (KAl(SO₄)₂·12H₂O) is an eco-oriented chemical widely used in water treatment, yet its concentration-dependent performance in active WBMs remains poorly quantified. This study systematically evaluated alum (0–10 lb/bbl) using a component-based approach and a field-representative polymer WBM, focusing on pH evolution, rheology, filtration, and volumetric swelling in both bentonite and grey marl (calcareous shale).

Alum caused strong acidification in all systems, driving the initial pH of the field WBM down from 10.1 to 4.6 at a concentration of 6 lb/bbl. In the field-representative mud, alum progressively improved rheological profiles up to a critical concentration of 6 lb/bbl, where plastic viscosity and yield point reached their peak performance zone due to temporary polymer–Al³⁺ interactions. Beyond these 6 lb/bbl thresholds, severe pH reduction below 4.0 promoted acid-catalyzed polymer degradation, causing rheological collapse and sharply increasing API fluid loss from 1.1 ml to 2.4 ml.

Swelling tests showed a monotonic reduction in sodium bentonite swelling, stabilizing at 22.77% expansion at 6 lb/bbl. Conversely, grey marl exhibited a non-linear response; swelling was initially minimized to 17.56% at 7 lb/bbl but experienced a distinct swelling reversal at higher dosages, rising back to 23.78% at 10 lb/bbl due to acid–carbonate reactions that undermined mechanical matrix integrity.

These quantitative results define a narrow operational window for alum in polymer-rich WBMs (≤ 6 lb/bbl) and demonstrate that carbonate-bearing shales suffer severe chemo-mechanical instability at elevated dosages, bounding alum's practical applicability in active drilling environments.

Research Paper Petroleum Engineering – Production

Evaluation of the Source Signatures of Selected Crude Oils from Niger Delta Using Biological Markers

https://doi.org/10.22050/ijogst.2026.583838.1781

Onojake M Chukunedum, Moses Ogbonaya, George U. Ozulu

Abstract Most of the productive crude oil and gas basins in the world which includes the Niger Delta is usually characterized by complex geological settings and diverse crude oil signatures. This study evaluates the use of molecular biomarkers particularly hopanes for the geochemical characterization and differentiation of crude oils from four major oil fields: Imo, Nembe, Soku, Bonga, Kwale and Owaza. Crude oil samples were collected directly from production lines and subjected to chromatographic separation and analysis using Gas Chromatography Mass Spectrometry (GC-MS). Diagnostic ratios such as Ts/(Ts+Tm), C29/C30 hopane, oleanane/C30 hopane, C31S/C31R and sterane/hopane (0.16 to 0.87) were computed to assess depositional environment, organic precursor input, thermal maturity, biodegradation status, and inferred age of source rocks. The results revealed that the Imo, Nembe, and Soku oil fields exhibit high oleanane indices (0.68 – 0.84), indicating deltaic depositional environments dominated by terrestrial organic matter and suggesting a Tertiary age for their source rocks. In contrast, the Bonga crude lacked oleanane but contained gammacerane (G/C30 = 0.12), pointing to a stratified marine origin with algal input. Thermal maturity indicators placed all samples within the low to moderate maturity window, with Ts/(Ts+Tm) ratios of 0.53 (Imo), 0.41 (Nembe), 0.42 (Soku), 0.52 (Bonga); 0.51(Kwale) and 0.51 (Owaza). These values are consistent with oils that have not yet reached peak thermal maturity, while biodegradation assessments using norhopane levels revealed different microbial alteration, with Imo and Soku oils being the least degraded. Multivariate statistical analysis was used to identify the genetic relationships among the crude oil samples. The study demonstrates the effectiveness of molecular biomarker analysis in differentiating crude oil sources within a petroleum province. These facts are of significant relevance to petroleum system modeling, reservoir correlation, and optimization of exploration strategy in hydrocarbon - rich basins like the Niger Delta

Research Paper Geophysics

Total organic carbon prediction using seismic attributes and well log data: A comparative study of six tree-based machine-learning models.

https://doi.org/10.22050/ijogst.2026.604515.1796

reda Alhasan, Mohammad Hossein Saberi, Mohammad ali Riahi

Abstract Total organic carbon (TOC) is a key parameter for evaluating source-rock potential, but laboratory Rock-Eval measurements are scarce and costly. Log-based proxies such as the ΔlogR method of Passey et al. (1990) are therefore widely used. In this study, we compare six tree-based regression models, AdaBoost, Random Forest, Extra Trees, Gradient Boosting, LightGBM, and XGBoost, for predicting TOC from seismic attributes in the Groningen gas field, the Netherlands. The target is ΔlogR-derived TOC from four Groningen wells (TJM-1, SCB-1, SDB-1, and SDB-10), not laboratory TOC. Negative proxy values were removed, leaving 98,861 samples. Test metrics measure agreement with this proxy over the Rotliegend and the Carboniferous source-rock interval. Feature selection retained seven seismic attributes. On an independent 20% hold-out set, Random Forest, Gradient Boosting, and XGBoost achieved the lowest test MSE (0.0315) and the highest test R² (0.8900–0.8901). These scores describe agreement with the ΔlogR proxy in the four training wells; they do not establish accuracy against laboratory TOC or spatial generalization beyond those wells.