Accounting
Vahab Montazeri; Atefeh Ghazi
Abstract
AbstractIt is essential to separate two immiscible liquids from gas to produce the light liquid, heavy liquid, and vapor phases. The separation of water from hydrocarbons is a practical example in the oil industry. For such separation in industry, three phase separator is used. In this study, different ...
Read More
AbstractIt is essential to separate two immiscible liquids from gas to produce the light liquid, heavy liquid, and vapor phases. The separation of water from hydrocarbons is a practical example in the oil industry. For such separation in industry, three phase separator is used. In this study, different parameter and the weight of the three-phase separator was optimized with the genetic algorithm (G.A.) and finally, the total cost of manufacturing the separator was decreased. Different types of three-phase separators are vertical, horizontal, and spherical. The separator works in the operating condition of 172 kPa and 445 K, respectively and the real weight of the separator is 8131 kg. For the optimization target, the flow of vapor, light liquid, and heavy liquid was considered constant during the optimization process. The objective function (O.F.) is obtained from the weight of the separator and 3 multiparameter equations. Also, 7 parameters which include: separator aspect ratio (L/D), the height of heavy liquid (HHL), height of light liquid (HLL), hold-up time (TH), surge time (TS), low liquid level (HLLL) and vapor level (Hv) are used in G.A. as constraints. The weight of the optimized separator was calculated 6001 kg approximately. So, with this method, the total weight of the separator decreases by about 26.2 % as compared to the real weight of the separator. On the other hand, the maximum difference between the answers was 3.3%, which is acceptable. Also, error analysis of the predicted results is calculated by mean absolute percentage error (MAPE) for 7 design parameters of the three-phase separator and separator weight, which are in an acceptable level of accuracy. The presented approach can have potential application for the development of low-cost manufacturing of three-phase separators in the petroleum industry.
Petroleum Engineering – Reservoir
Temple N Chikwe; Mudiaga Onojake
Abstract
The geochemical investigation of trace metals in crude oils from some producing oil fields in the Niger Delta, Nigeria, was carried out to ascertain the petroleum source rocks and organic matter deposits. The concentrations of trace metals in crude oil samples obtained from eight producing fields from ...
Read More
The geochemical investigation of trace metals in crude oils from some producing oil fields in the Niger Delta, Nigeria, was carried out to ascertain the petroleum source rocks and organic matter deposits. The concentrations of trace metals in crude oil samples obtained from eight producing fields from Niger Delta, Nigeria, were analyzed using a 700 model Perkin Elmer atomic absorption spectrophotometer. The results showed the following ranges for the trace metals: Cu (0.01–0.04 mg/kg), Fe (0.05–5.90 mg/kg), Ni (0.09–0.72 mg/kg); and V (0.008–1.05 mg/kg). Pb and Zn were lower than 0.01 mg/kg. Trace metal ratios such as V/Ni, V/Fe, and (V/V + Ni) were used to unravel the genetic correlation among the oils. All the crude samples except the sample from Nembe South-2 have a V/N ratio lower than 1.0, indicating that the organic materials produced the petroleum source rock. A cross plot of V/Ni revealed two genetic families for the crude oils, derived from a terrestrial and marine origin, which was confirmed by the ternary plot of V, Ni, and Fe, discriminating the crude oils from the producing fields into two distinct groups. The V/(Ni + V) of smaller than 0.5 showed that most crude oils were deposited in an oxic environment. A cross-plot of V/(Ni + V) and V/Fe showed a weak correlation, suggesting that it could not substitute for the V/Ni ratio in determining the origin and depositional environment of crude oil samples. Therefore, an in-depth knowledge of the concentration of trace metals, especially vanadium and nickel, within an environment during oil exploration is essential in developing new oil locations.
